552 Results
View results:
Sort by:
Comparative Analysis for RANS, URANS, and DDES Turbulence Models
What is the difference between the RANS, URANS, and DDES turbulence models?
Double-Sided Stiffening (Splice)
How can I model a timber beam with stiffening on both sides? (splice)
Plastic Hinges
How do I define a plastic hinge in RFEM 6?
Importing Surfaces from Rhino into RFEM 6
Why are not all surfaces transferred when importing surfaces from Rhino into RFEM 6?
Advantages of CFD Simulation
What are the advantages of CFD simulation compared to conventional experimental tests?
Direct vs. Iterative Solver
The calculation in RFEM 6 takes a very long time, but the processor utilization of my system is low. Why is this?
Setting of I-Beam Flange Support for Design in Structure Stability Add-on
In the Steel Design add-on, I have set the boundary conditions in such a way that the I-beam flange is restrained against the horizontal displacement. I then calculated the critical load factors using the Structure Stability add-on, but with no effect on the critical load factor value. What is the reason for this?
Activating Steel Fiber Concrete Design in "Concrete Design" Add-on
How can I activate the design with steel fiber-reinforced concrete in the "Concrete Design" add-on for RFEM 6?
Imperfection Case
There is no "Imperfection" action category. How can I create an imperfection load case?
Pipe as Shear Key in RF-/JOINTS Steel – Column Base Add-on Module
How do I define a pipe as a shear key in RF‑/JOINTS Steel – Column Base add-on module?
Are the solids with a common surface automatically connected rigidly to each other?
Are the solids with a common surface automatically connected rigidly to each other?
Steady-State or Transient Simulation for Parapet in RWIND
What is the most accurate CFD method for the wind simulation of parapets?
- 005450
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Aluminum Design for RFEM 6
- Aluminum Design for RSTAB 9
- Form-Finding for RFEM 6
- Steel Structures
- Aluminum and Lightweight Structures
- Temporary Structures
- Tensile Membrane Structures
- Structural Analysis & Design
- Form-Finding and Cutting Patterns
- Dynamic and Seismic Analysis
- Eurocode 3
- Eurocode 9
- ANSI/AISC 360
- ADM
Temporary Structures
I would like to analyze temporary structures. Which programs do you recommend?
Power Plants and Conveyor Structures
Which programs can I use to design power plants and conveyor structures?
Scaffolding and Rack Structures
We are looking for a program for scaffolding and rack structures. Is Dlubal Software suitable for this?
Tensile Membrane Structures
Which Dlubal programs do I need for tensile membrane structures?
Aluminum and Lightweight Structures
I would like to design an aluminum structure. Is it possible to use RFEM or RSTAB for this?
Cable and Tensile Structures
I would like to analyze cable and tensile structures. Is it possible to use RFEM or RSTAB for this?
Programs for Laminate and CLT Structures
Which programs do I need for laminate and sandwich structures, or cross-laminated timber (CLT)?
Programs for Timber Structures
Which Dlubal Software programs can I use to calculate and design timber structures?
Design of Hydraulic Steel Structures
Can I analyze and design hydraulic steel structures with the Dlubal programs?
- 005437
- RFEM 6
- RSTAB 9
-
- Steel Design for RFEM 6
- Steel Design for RSTAB 9
- Steel Joints for RFEM 6
- Torsional Warping (7 DOF) for RFEM 6
- Torsional Warping (7 DOF) for RSTAB 9
- Steel Structures
- Structural Analysis & Design
- Stress Analysis
- Stability Analysis
- Warping Torsion Analysis
- Steel Connections
- Cold-Formed Sections
- Eurocode 3
- ANSI/AISC 360
- CSA S16
- IS 800
- GB 50017
- SP 63.13330
- BS 5950-1
- AS 4100
- SIA 263